運揚有限公司 WANCO LIMITED
Hipot Tester
Hipot Tester
TOS5101
2017-04-18 16:32
2017-05-02 15:52
Product Description
Hipot Tester
耐高溫測試儀
Model : TOS5101
The Kikusui TOS5101
* Specification
Output block
Applied Voltage 0 to 5/ 0 to 10 kV AC and DC
AC
Maximum Rated 500VA / 10 kV, 50 mA
Waveform Commercial line waveform
Voltage Regulation Max. 15% (for max. rated load to no load)
Switching Use of a zero turn-on switch
DC
Applied Voltage 50W / 10 kV, 5 mA
Ripple 100 Vp-p typ. at 10 kV, no load
200 Vp-p typ. at max. rated output
Maximum Rated Max. 3% (for max. rated load to no load)
Output Voltmeters
Analog Scale 10 kV full scale , AC/DC
Class JIS Class 2.5
Accuracy ±5% of full scale
AC Indication Mean value response / rms value scale
Digital Full Scale 5 kV/ 10 kV full scale
Accuracy ±1.5% of full scale
AC Response Mean value response / rms value display
Ammeter
Digital Accuracy ±(5% + 20μA) of upper cutoff current
AC Response Mean value response / rms value displayType of Judgement
Pass/fail Judgement Function
●FAIL judgement
*When current detected above upper cutoff current
*When current detected below lower cutoff current
(FAIL signal generated when FAIL judgement made)
● PASS judgement
*When set time has elapsed and no abnormality is
detected
Upper cutoff current setting range AC: 0.1 to 55 mA DC: 0.1 to 5.5 mA
Lower cutoff current setting range AC: 0.1 to 55 mA DC: 0.1 to 5.5 mA
Judgement Accuracy ±(5% of upper cutoff current + 20μA)
Current Detection Integration of current absolute value followed
by comparison with reference value.
Calibration With rms value of sine wave using a pure
resistance load.
No-load output voltage required
for detection
Approx. 970 V when set to 50 mA AC
Approx. 160 V when set to 5 mA DC
Test Time Setting Range 0.5 to 999 sec (±10 ms) (timer-off function
provided)
Accuracy ±20 ms
Line Voltage 100V±10%, 50/60 Hz (Nominal voltages of
110V, 120V, 220V, 230V and 240V
available as factory options.)
Power Requirements
for line voltage of 100 V Max. 50 VA under no-load conditions
/ Approx. 600 VA at rated load
for line voltage of 100 V to 200 V Max. 50 VA under no-load conditions
/ Approx. 600 VA at rated load
for line voltage of 220 V to 240 V Max. 50 VA under no-load conditions
/ Approx. 610 VA at rated load
Electromagnetic compatibility (EMC) *3 Conforms to the requirements of the
following directive and standard.*2
EMC Directive 2004/108/EC
EN 61326-1
EN 61000-3-2
EN 61000-3-3
Under following conditions
1. Used HV test leadwires which is
supplied.
2. No discharge in testing.
3. Used the shielded cable which length is
less than three meters when the SIGNAL
I/O is used.
Safty Conforms to the requirements of the following
directive and standard.
Low Voltage Directive 2006/95/EC
EN 61010-1 Pollution degree 2
U L1244( T h e U L - a p p r o v e d p r o d u c t s
with input voltage of 120VAC satisfy the
UL1244 standerd.)
Insulation resistance 30 MΩ or more (500 V DC)
Hipot 1390 VAC, 2 seconds [between the AC LINE and chassis]
1200 VAC, 1 second [UL-approved products only]
Environment Specification range : 5 °C to 35°C / 20 %rh to 80 %rh
Operable range : 0 °C to 40°C / 20 %rh to 80 %rh
Storage range : -20 °C to 70 °C / 80 %rh or less
Dimensions (maximum) 430[16.9 inch] W × 177[6.97 inch] (195[7.68 inch]) H × 370[14.6 inch] (450[17.7 inch]) D mm
Weight
Lie voltage of 100 V Approx. 21 kg (Approx. 46.30 lbs)
Line voltage of 100 V to 120 V Approx. 23 kg (Approx. 50.70 lbs)
Line voltage of 220 V to 240 V Approx. 24 kg (Approx. 52.91 lbs)
Accessories
High-voltage test lead TL01-TOS (max.allowablevoltage: 5 kV /1.5m)
TL03-TOS (max.allowablevoltage: 10 kV /1.5m)
Others 14-pin amphenol plug (assembled)